IT업계의 치열한 경쟁속에 살아 남으려면 자신의 능력을 증명하여야 합니다. 국제승인을 받는 IT인증자격증을 많이 취득하시면 취직이든 승진이든 이직이든 모든 면에서 이득을 볼수 있습니다. 최근 Juniper인증 JN0-694시험에 도전하는 분이 많은데 ITExamDump에서 Juniper인증 JN0-694시험에 대비한 가장 최신버전 덤프공부가이드를 제공해드립니다.
우선 우리ITExamDump 사이트에서Juniper JN0-694관련자료의 일부 문제와 답 등 샘플을 제공함으로 여러분은 무료로 다운받아 체험해보실 수 있습니다.체험 후 우리의ITExamDump에 신뢰감을 느끼게 됩니다. ITExamDump에서 제공하는Juniper JN0-694덤프로 시험 준비하시면 편안하게 시험을 패스하실 수 있습니다.
시험 번호/코드: JN0-694
시험 이름: Juniper (Enterprise Routing and Switching Support, Professional (JNCSP-ENT))
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 36 문항
업데이트: 2013-09-15
Juniper JN0-694인증시험은 전문적인 관련지식을 테스트하는 인증시험입니다. ITExamDump는 여러분이Juniper JN0-694인증시험을 통과할 수 잇도록 도와주는 사이트입니다. 여러분은 응시 전 저희의 문제와 답만 잘 장악한다면 빠른 시일 내에 많은 성과 가 있을 것입니다.
Juniper인증 JN0-694시험을 통과하여 자격증을 취득하여 IT 업계에서의 자신의 자리를 지키려면 많은 노력이 필요합니다. 회사일도 바쁜데 시험공부까지 스트레스가 장난아니게 싸이고 몸도 많이 상하겠죠. ITExamDump는 여러분을 위해 최신Juniper인증 JN0-694시험에 대비한Juniper인증 JN0-694덤프를 발췌하였습니다. Juniper인증 JN0-694덤프는Juniper인증 JN0-694시험의 기출문제와 예상문제가 묶어져 있어 시험적중율이 굉장히 높습니다. 쉽게 시험을 통과하려면ITExamDump의 Juniper인증 JN0-694덤프를 추천합니다.
만약 아직도Juniper JN0-694인증시험 위하여 많은 시간과 정력을 소모하며 열심히 공부하고 있습니까? 아직도 어덯게하면Juniper JN0-694인증시험을 빠르게 취득할 수 있는 방법을 못찿고 계십니까? 지금ITExamDump에서Juniper JN0-694인증시험을 안전하게 넘을 수 있도록 대책을 내드리겠습니다. 아주 신기한 효과가 있을 것입니다.
JN0-694 덤프무료샘플다운로드하기: http://www.itexamdump.com/JN0-694.html
NO.1 Your Layer 2 network uses VLAN IDs 100 through 400 and you are required to load-balance
these VLANs between two different root bridges. You are currently using the default RSTP settings
and notice that all VLANs are using the same root bridge.
How do you ensure the VLANs are load-balanced between two root bridges?
A. Configure MSTP with two MSTI regions and split the VLAN range between them.
B. Configure VSTP with two VLAN groups and split the VLAN range between them.
C. Configure two RSTP instances and split the VLAN range between them.
D. Configure STP and RSTP and split the VLAN range between them.
Answer: A
Juniper기출문제 JN0-694 JN0-694 JN0-694 JN0-694자료
NO.2 Two neighboring routers are able to form an OSPF adjacency, but are not able to establish an
IBGP neighborship.
What are two reasons for the IBGP neighborship problem? (Choose two.)
A. One of the devices has a misconfigured BGP peer address.
B. One or both of the connected interfaces are missing the family iso statement.
C. OSPF has a lower route preference than BGP .
D. A firewall filter on one of the interfaces is blocking TCP traffic.
Answer: B,C
Juniper JN0-694최신덤프 JN0-694 dumps
NO.3 You are having problems redistributing RIP routes into OSPF. Your Junos device has the
following configuration:
[edit protocols ospf]
user@router# show
import my-policy;
area 0.0.0.0 {
interface ge-0/ 0/ 0.0;
interface ge-0/ 0/ ;
interface ge-0/ 0/ {
passive;
}
}
What would resolve the problem?
A. Apply my-policy as an export policy under the [edit protocols rip] hierarchy.
B. Apply my-policy as an import policy under the [edit protocols rip] hierarchy.
C. Apply my-policy as an export policy under the [edit protocols ospf] hierarchy.
D. Use the area-range parameter instead of a routing policy.
Answer: D
Juniper pdf JN0-694 JN0-694 JN0-694자료
NO.4 Your Junos device is dropping certain traffic flows, while allowing other traffic flows to pass
through the device unaffected.
Which CoS component is causing this problem?
A. BA classification
B. RED
C. MF classification
D. Rewrite rules
Answer: D
Juniper자격증 JN0-694 JN0-694기출문제 JN0-694 pdf
NO.5 You are implementing Q-in-Q tunneling on an EX Series switch. You want the tunnel to support
all C-VLANs; however, only some VLANs are able to send traffic across the tunnel.
Switch-1 has the following configuration:
[edit vlans]
user@Switch-1# show
v100 {
vlan-id 100;
interface {
ge-0/ 0/ 0.10;
ge-0/ 0/1.20;
}
dot1q-tunneling {
customer-vlans [ ];
}
}
What would solve this problem?
A. Add family ethernet-switching to the tunnel-side interface on Switch-1.
B. Implement RSTP .
C. Q-in-Q tunneling will not work in this scenario; use a Layer 2 VPN instead.
D. Remove the customer-vlans statement.
Answer: C
Juniper dump JN0-694 JN0-694 dumps JN0-694 JN0-694
NO.6 You are troubleshooting a problem where an OSPF adjacency between two neighboring
routers will not form.
What are two reasons for this problem? (Choose two.)
A. One or both of the connected interfaces are missing the family inet statement.
B. One or both of the connected interfaces are missing the family iso statement.
C. The connected interfaces are not on the same subnet.
D. Another IGP is running on one or both of the routers, overriding OSPF.
Answer: B,D
Juniper자료 JN0-694 JN0-694 dump JN0-694
NO.7 You observe that a router is using an unusually high amount of CPU cycles.
You determine that continuous SPF calculations in OSPF are being performed.
What are two reasons for this problem? (Choose two.)
A. The wrong authentication keys between the OSPF neighbors are used.
B. The interface MTU is mismatched between the OSPF neighbors.
C. There are duplicate router IDs within the OSPF area.
D. An OSPF adjacency is flapping.
Answer: C,D
Juniper자격증 JN0-694 JN0-694 JN0-694자료
NO.8 Your switch is experiencing a problem where a port that should have only one host connected
occasionally shows that multiple MAC addresses are being learned.
Which configuration setting would ensure that no extra hosts can join the network using this switch
port?
A. mac-limit
B. no-mac-learning
C. persistent-learning
D. bpdu-block-on-edge
Answer: D
Juniper시험문제 JN0-694 JN0-694 JN0-694
ITexamdump의 MB6-870덤프의 VCE테스트프로그램과 70-464덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 FCNSP.v5시험에 대비한 고품질 덤프와 ICGB시험 최신버전덤프를 제공해드립니다. 최고품질 312-50v8시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기